Ofna-racing Ultra LX Pro (GT LX) User Manual download pdf (Page 22)

3 X 8mm

Washer

3mm Nylon

Locknut

3 x 5mm Screw

3 x 20mm

Cap Screw

* Place the clutch shoes

with the clutch springs

over the 3 pins of the

flywheel.

Using a screw driver as a lever,

bend the small end of the

clutch spring behind the

clutch nut and press

down to snap shoe in

place.

* Fit the flywheel using a cross

wrench or deep socket.

If engine turns when tightening,

hold piston with large thick tie-wraps

and hard wood in exhaust port.

Do not use metal, it will

damage engine.

#10098

SG Nut

& Shim KiT

ASSEMBLY OF THE CLUTCH INTO ENGINE

3 x 10mm

Tapping Screw

#10016

Air Filter

Sponge

Refills

#10017 - Blue

#10018 - Yellow

#10019 - Rose

Foam Air filters Unit

#10014 - Mount Wire

#10021 - Black

#10027 - Yellow

#10028 - Pink

#10029 - Blue

Air Filter Connector

Nylon Strap

( Small )

Nylon Strap

( Small )

You must oil foam filter before use.

Filter will not work if not oiled.

Clean with soap and water only.

You will damage foam if washed

if fuel!

ASSEMBLY OF THE AIR FILTER

#10102

Clutch Spring

#10010

Clutch Shoes

Black Type

* Shoes are

trailing.

3 x 8mm

Washer

Misc. Hardware

#10099

#34110

5x10x4mm

Ball Bearing

#34110

5x10x4mm

Ball Bearing

#10040 (stock)

3 Pin

Flywheel, Taper

#10043

3 Pin

Flywheel, Fan

#10091

Clutch Nut

screw type

3 x 5mm

Screw

#10330

Brass, Corn

(large hole)

#10329

Brass, Corn

(sml hole)

30481

3 x 20mm

Hex Screw

30481

3 x 20mm

Hex Screw

30481

3 x 20mm

Hex Screw

#30480

Engine Mount

#10398 - 12T

#10399 - 13T

#10400 - 14T (stock)

#10401 - 15T

#10402 - 16T

#10403 - 17T

#10404 - 18T

Clutch Bells

SEE NOTES

ABOVE

Notes:

Non-Pull Start Engines...

• Alum. Washer behind the flywheel is not needed when using Force engines or similar types. O.S. Engines will

require washer spacer.

• To check!..place the brass corn against the engine bearing, then flywheel. You should be covering one or two

thread of the engine shaft. If this is the case, you do not need an additional washer behind the flywheel.

You must cut the engine shaft if too long. Count 6 threads in front of the flywheel and mark. This is all you need to

tighten the clutch nut and mount the flywheel.

Force Pull Start Engine w/threaded shalf...

• Force Pull Start Engines required NO spacer and no shaft cutting. The engines comes with an alum cast driver

washer, you use this part as the spacer, not the alum. washer shown. Also, use the special flywheel brass corn.

This corn fits the thread shaft diameter so you can tighten the flywheel against the drive hub.

Note

SG Shaft

Threaded

Shaft

Options

Clutch Spring

10100 - Springs, Polished, Med.

10101 - Spring, Gray, Hard

10102 - Spring, Black, Stock

Clutch Shoes, 3 shoe clutch

10010 - Shoes, Carbon Material, Black

10011 - Shoes, Alum. CNC Blue, Lite Weight

10012 - Shoe, Alum. CNC Purple, Med. Weight

Option

10799

Flywheel Wrench

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 31 32

Comments to this Manuals

No comments

Ofna-racing Ultra LX Pro (GT LX) User Manual Page 22

Comments to this Manuals

Related products and manuals for Cars Ofna-racing Ultra LX Pro (GT LX)